|
| |
|
|
| |
Products >> Mould Parts |
|
| |
: Mould
Accessories : |
|
|
Cooling Baffles
Sprial Cooling Cores
Locking Latch
Straight Block Set
Taper Interlock
Parting Lock
Taper Block Set
 |
|
Baffle Configuration shows a typical water baffle, illustrates some considerations in core cooling. The water flows all the way into the core, ensuring uniform, complete heat removal. It is critical to bring water to the end of the core pin to allow optimum cooling at the innermost section of the core region.
When cutting a baffle coolant drop, designers should make it larger in diameter than the feeder tube in order to prevent a flow obstruction from occurring. The cross-sectional area of each side of the drop channel should equal the area of the feeder tube. In a typical baffle tube assembly, a water channel is drilled into the area to be cooled. An intersecting water channel provides water flow that is diverted up one side of the baffle and down the other.
|
| |
 |
 |
| |
Cooling elements connected in series that are used to cool pins, hollow areas, and deep draws. Used over very short runs where coolant pressure drops are not critical, in molds with few cavities from side to side, and in molds with large diameter channels and baffles. Generally metal blades are inserted into a drilled channel, dividing it into two semi-circles. The first semi-circle is the inlet, while the other is the outlet. Now Plastic Cooling Baffles are developed for easy insertion and effective cooling. They are non rusty and leak proof.
Just drill the hole to the standard size and insert the cooling baffle according to your required length.
|
 Top
Sprial Cooling Cores :
•The Endeavour spiral cooling cores are very efficient in cooling cores.
• They are manufactured from Aluminum and temperature resistant plastics.
• They are used in Injection Moulds.
• Available in standard length and can be cut to your size
• Max. processing temp. 125°C
Top
|
|
| |
Top
|
Endeavour Straight block sets are manufactured as a standard accessory for the mould’s alignment. They are hardened and ground with the desired hardness. They can be used for Core & Cavity plates alignment. These Taper Blocks are ready to use and should be fitted very precisely on the mould for best performance.
|
 |
Model No. |
A |
B |
C |
D |
E |
F |
f |
J |
H |
K |
L |
M |
N |
ESB 50 |
50 |
21.5 |
30 |
17 |
21.5 |
10.5 |
6.5 |
11 |
8 |
34 |
16 |
5 |
8 |
ESB 75 |
75 |
36 |
50 |
25 |
36 |
16.5 |
10.5 |
18 |
12.5 |
50 |
19 |
5 |
12 |
ESB 100 |
100 |
45 |
65 |
35 |
45 |
16.5 |
10.5 |
22 |
15 |
70 |
19 |
5 |
12 |
ESB 125 |
125 |
45 |
65 |
45 |
45 |
16.5 |
10.5 |
22 |
20.5 |
84 |
25 |
5 |
12 |
|
Top
|
Endeavour Taper Interlocks are manufactured as a standard accessory for the mould’s alignment. They are hardened and ground with the desired hardness. They can be used for Core & Cavity alignment. These Taper Interlocks are ready to use and should be fitted very precisely in mould for best performance.
|
|
Catalog No. |
L |
V |
E |
M |
A |
 |
PART NO. |
D |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Top
Parting Lock :
Parting locks are used in moulds for pulling the plates to a desired limit. They act like puller. The unique design and selection of right material makes the performance of application more better.
Features :
• Place the Parting lock bolt on moving side of the mold.
• Install min. 4 nos. on one mold. 2 nos. each on both sides of the plate.
• After placement of the Parting locks on the plate, turn the bolt to 90º and plastic lock will expand.
• Do not apply any lubricant on plastic part. Doing so will reduce the friction and grip.
• Use H 7 reamer in hole of the mold plate with + 0.1 mm range.
• Mould weight < 100 kgs , using 4 nos. of 13 E Parting lock.
• Mould weight < 500 kgs , using 4 nos. of 16 E Parting lock.
• Mould weight < 1000 kgs , using 4 nos. of 20 E Parting lock.
• If more load to be pulled then above limit then use more nos. of Parting locks to be used. i.e. 6 or 8 nos.
• Very easy to assemble and disassemble without dismounting the mold from the machine.
Top
Endeavour Taper block sets are manufactured as a standard accessory for the mould’s alignment. They are hardened and ground with the desired hardness. They can be used for Core & Cavity as well Sliding Core alignment. These Taper Blocks are ready to use and should be fitted very precisely in mould for best performance.
All dimensions are in MM
Top
|
|
|
